Skip to content
GetMCQs.com – Competitive Exam MCQs & Quizzes
  • Home
  • Quiz
  • All MCQs
  • Aptitude
    • Height-and-Distance
    • series
    • Time and Distance
    • Time and Work
    • Train
  • Art
    • Accounting
    • Business and Commerce
    • Costing
    • eCommerce
    • Economics
    • Financial Management
    • GST
    • Insurance
  • Computer
    • Basics of Computer Science MCQs
    • Operating System
    • MS Office
      • MS Word MCQs
      • MS Excel MCQs
      • MS PowerPoint MCQs
  • Engineering
    • Chemical Engineering
    • Environmental Engineering MCQs
    • Civil Engineering
    • Electrical Engineering
    • Mechanical Engineering
    • Software Engineering MCQs
  • English
  • Physics MCQs
  • Chemistry
  • Biology
  • General Knowledge
  • Everyday Science

Mechanical Engineering MCQs

In a compressed air system, the temperature of air discharged from the air motor is __________ than the initial compressor intake temperature.

September 13, 2025 by Admin
more
less
✅ The correct answer is option B.
Categories Compressors, Gas Dynamics and Gas Turbines MCQs, Engineering, Mechanical Engineering Tags Compressors, Engineering MCQs, Gas Dynamics and Gas Turbines MCQs, Mechanical Engineering MCQs Leave a comment

The temperature of the inner luminous cone of neutral flame is about

September 13, 2025 by Admin
1000° C
1250° C
2100° C
3200° C
✅ The correct answer is option D.
Categories Engineering, Mechanical Engineering, Workshop Technology MCQs Tags Engineering MCQs, Mechanical Engineering MCQs, Workshop Technology MCQs Leave a comment

Which of the following refrigerant has the lowest freezing point?

September 13, 2025 by Admin
R-11
R-12
R-22
Ammonia
✅ The correct answer is option C.
Categories Engineering, Heat Transfer, Refrigeration and Air Conditioning MCQs, Mechanical Engineering Tags Engineering MCQs, Heat Transfer, Mechanical Engineering MCQs, Refrigeration and Air Conditioning MCQs Leave a comment

The hole to be drilled for tapping is __________ the outside diameter of the thread on the tap.

September 13, 2025 by Admin
equal to
smaller than
greater than
✅ The correct answer is option B.
Categories Engineering, Mechanical Engineering, Production Engineering MCQs Tags Engineering MCQs, Mechanical Engineering MCQs, Production Engineering MCQs Leave a comment

The knocking tendency in spark ignition engines may be decreased by

September 13, 2025 by Admin
controlling the air-fuel mixture
controlling the ignition timing
controlling the exhaust temperature
reducing the compressi
✅ The correct answer is option D.
Categories Engineering, IC Engines and Nuclear Power Plants MCQs, Mechanical Engineering Tags Engineering MCQs, IC Engines and Nuclear Power Plants MCQs, Mechanical Engineering MCQs Leave a comment

One molecule of oxygen is __________ times heavier than the hydrogen atom.

September 13, 2025 by Admin
12
14
16
32
✅ The correct answer is option D.
Categories Engineering, Mechanical Engineering, Thermodynamics MCQs Tags Engineering MCQs, Mechanical Engineering MCQs, Thermodynamics MCQs Leave a comment

The specific gravity of petrol is about

September 13, 2025 by Admin
0.75
0.85
0.95
1.25
✅ The correct answer is option A.
Categories Automobile Engineering MCQs, Engineering, Mechanical Engineering Tags Automobile Engineering MCQs, Engineering MCQs, Mechanical Engineering MCQs Leave a comment

The draught in locomotive boilers is produced by a

September 13, 2025 by Admin
chimney
centrifugal fan
steam jet
none of these
✅ The correct answer is option C.
Categories Engineering, Mechanical Engineering, Steam Boilers and Engines MCQs Tags Engineering MCQs, Mechanical Engineering MCQs, Steam Boilers and Engines MCQs Leave a comment

Trepanning is an operation of

September 13, 2025 by Admin
making a cone-shaped enlargement of the end of a hole
smoothing and squaring the surface around a hole
sizing and finishing a small diameter hole
producing a hole by re
✅ The correct answer is option D.
Categories Engineering, Mechanical Engineering, Production Engineering MCQs Tags Engineering MCQs, Mechanical Engineering MCQs, Production Engineering MCQs Leave a comment

In centreless grinding, work place centre will be

September 13, 2025 by Admin
above the line joining the two wheel centres
below the line joining the two wheel centres
on the line joining the two wheel centres
at the intersection of
✅ The correct answer is option A.
Categories Engineering, Mechanical Engineering, Production Engineering MCQs Tags Engineering MCQs, Mechanical Engineering MCQs, Production Engineering MCQs Leave a comment
Older posts
Newer posts
← Previous Page1 … Page429 Page430 Page431 … Page536 Next →
GetMCQs:

  

  • Arts Subjects MCQs
  • Aptitude MCQs
  • Biology
  • Chemistry
  • English
  • Everyday Science
  • General Knowledge
  • Pedagogy
  • Psychology
  • Physics
  • Punjab Public Service Commission (PPSC) - Past Papers
  • Sociology

  

  • Chemical Engineering
  • Civil Engineering
  • Environmental Engineering
  • Mechanical Engineering
  • Software Engineering
  • Electrical Engineering

  

  • All Computer MCQs
  • Basics of Computer Science
  • Operating System
  • MS Word
  • MS Excel
  • MS PowerPoint

MCQs

2026 Antonyms MCQs Art Basic Chemical Engineering MCQs Basic General Knowledge MCQs Basics of Computer Science MCQs Chemical Engineering Chemical Process MCQs Civil Engineering Civil Engineering Mcqs MCQs Common Error Detection MCQs Computer Costing Engineering English Environmental Science MCQs Everyday Science MCQs Financial Management Fluid Mechanics MCQs General Anatomy Mcqs General Knowledge GK Idioms And Phrases MCQs Insurance International Finance and Treasury MCQs Islamic Studies Machine Design MCQs Management Mass Transfer MCQs Mechanical Engineering Medical MS Office One Word Substitution MCQs Operating System Physiology Mcqs PPSC PPSC Past Papers Related Pair of Words MCQs Sentence Completion MCQs Software Engineering MCQs Sports MCQs SSC Synonyms MCQs Theory of machines MCQs UPSC
© 2026 GetMCQs.com – Competitive Exam MCQs & Quizzes • Built with GeneratePress